
Reading a Servo Drive Order Code Before You Order a Replacement: Rexroth HCS01.1E Current and Suffix Classes, Kollmorgen S7000 Output Stage, and Parker SLVD Supply Voltage
A servo drive order code is a configuration record, not merely a model name. It identifies the electrical class, feedback hardware, communications options, firmware, and other fitted features. Yet two seemingly similar catalogue entries can describe materially different equipment. The Rexroth HCS01.1E family is a clear example: identical-looking order-code fragments do not guarantee identical power, voltage, filtering, or enclosure ratings. A reliable replacement decision therefore depends on three layers of evidence: the complete manufacturer order code, the physical nameplate on the unit, and the manufacturer datasheet. This guide explains how to compare drive listings without assuming that shared characters imply interchangeability.
The Nameplate Is Not the Order Code
A drive’s model marking may identify its family, while the full order code records the delivered configuration. The order code normally combines the base type and generation, a current or power field, a voltage class, control-section options, communication and feedback options, and trailing software or special-code groups. The physical nameplate is essential, but it should not be treated as a substitute for the ordering documentation. It may identify electrical ratings without fully describing the installed options.
Our catalogue demonstrates this point with two Rexroth HCS01.1E variants. The Rexroth HCS01.1E-W0018 servo drive is listed as “REXROTH HCS01.1E-W0018-A-03-B-ET-EC-NN-L4-NN-FW.” Our listing states 3 x 400-480 V AC input, an 18 A rated current, a 7.5 kW power rating, EtherCAT communication, a Basic control section with encoder evaluation, an integrated L4 line filter, 3.2 kg weight, and dimensions of 160 x 240 x 70 mm.
Another listing, “REXROTH HCS01.1E-W0018-A-03-B-ET-EC-NN-L3-NN-FW,” is listed at 230 V AC supply with a 1.8 kW rating, EtherCAT, 16-bit feedback resolution, an operating ambient range of 0 to 55 C, and IP65 protection. The shared W0018 portion therefore does not define the delivered unit by itself. The digits after the current field and the trailing suffix groups distinguish these listings.
Do not resolve such a conflict by guessing a decoding rule. The exact manufacturer order code, the unit’s nameplate, and the manufacturer datasheet settle it. Catalogue text is supporting information, but it cannot override the evidence attached to the physical drive.
Current Class and Power Rating Are Separate Columns
The current field in a servo-drive code generally identifies a device capability, not the motor that may safely be connected. Rated current, peak current, motor power, and ambient or cooling conditions answer different questions. A drive may be capable of delivering its stated output under specified conditions without being able to accelerate every motor rated at the same nominal power.
Several listings illustrate the distinction:
- The Rexroth HCS01.1E W0018 L4 listing states 18 A rated current and a 7.5 kW power rating.
- The Rexroth HCS01.1E W0018 L3 listing states a 1.8 kW rating but does not provide the same current field in the supplied brief.
- The Rexroth HCS01.1E W0054 listing states 5.4 kW rated power, 12 A input current, and 8 A output current.
- The Rexroth HCS01.1E W0003 listing states 0.3 kW rated power.
- The Allen Bradley listing states 22 A output for a 10 HP / 7.5 kW drive.
- The Parker SLVD2ND listing states 2 HP / 1.5 kW.
The Rexroth W0054 example is particularly useful because input and output current are presented separately. That distinction matters when judging a complete installation. The Allen Bradley 1336Z-SB010-N, by contrast, is listed with 380-480 V AC input, a 10 HP / 7.5 kW classification, 22 A output, and closed-loop vector control. The Mitsubishi FR-CV-7.5K is a different category: our listing describes a 7.5 kW MELSERVO regenerative converter for compatible MR-J4-700B systems, including approximately 46 A of regenerative power handling.
When comparing a replacement, preserve these categories as separate columns. Do not convert one into another without the manufacturer’s data. Also verify what the listing means by “rated” or “dependent on motor configuration.” Those phrases determine whether a motor match can be made from catalogue information alone.
Feedback and Interface Suffixes Decide Usability
Order-code suffixes often determine whether a drive can be commissioned with an existing motor and control network. In the Rexroth order codes, the ET group identifies EtherCAT, while EC identifies encoder evaluation. These letters are hard constraints. An EtherCAT axis cannot simply be substituted for a SERCOS III drop because the master, wiring, device description, and network configuration must all agree.
A listing that names both EtherCAT and SERCOS III interfaces still requires confirmation of the firmware option actually fitted. The Rexroth HCS01.1E W0054 listing names both interfaces and lists position, speed, and torque control. That does not mean every communication option is active in every delivered unit. The relevant firmware and ordering documentation must establish which option is installed.
Feedback matching is equally exacting. The HCS01.1E W0018 L3 listing states 16-bit feedback resolution. The LUST A-DS012.1 is listed with 17-bit absolute encoder feedback and pulse, analog, and RS-485 interfaces. The Kollmorgen S70602 listing specifies encoder feedback, while the Parker SLVD-N listing supports encoder or resolver feedback.
Resolution can affect commutation accuracy and low-speed smoothness, but it is not the only compatibility criterion. Battery-backed or mult-turn absolute feedback may change the replacement’s commissioning and storage requirements. Resolver pole-pair data must also match the motor. Connector pinout must be confirmed because a drive with encoder-evaluation hardware but the wrong feedback connector kit may be unusable on arrival.
Supply Voltage, Control Voltage and Enclosure Class
The listings cover several distinct supply classes: 120/240 V AC, 200-240 V AC, 230 V AC, 380-480 V AC, and 3 x 400-480 V AC. The HCS01.1E W0018 L4 and L3 listings demonstrate why a shared current field cannot define electrical compatibility. One is listed for 3 x 400-480 V AC, while the other is listed for 230 V AC.
Supply voltage is not a transformer-only consideration. The internal DC bus, braking path, insulation coordination, and electrical clearances are designed for a particular class. As stated in the technical brief, a 400 V-class drive fed from a 230 V supply loses available torque, while a 230 V-class drive fed from 400 V is destroyed. Confirm phase count and frequency as well as nominal voltage.
Several drives also require a separate 24 V DC control supply. The short Rexroth HCS01.1E-W0018-A-03 listing states 24 V DC control supply. The Parker SLVD-N servo drive SLVD2NSE listing states 220-240 V AC three-phase, 50/60 Hz with 24 V DC control input. Removing a drive from service without identifying the control circuit can also affect its safe state.
Environmental requirements add another constraint. IP20 cabinet-mounted units require an enclosure that provides suitable protection. The HCS01.1E W0018 L3 listing states IP65, while the HCS01.1E W0003 and W0054 listings state IP20. The Parker SLVD2ND is listed in a NEMA 1 enclosure of about 10 kg. IP codes and NEMA enclosure types come from different test schemes and must not be treated as interchangeable. Panel mounting also depends on the panel’s ingress protection and heat transfer through the mounting plate.
Motor Compatibility Is a Second Matching Problem
After confirming the drive’s voltage and interfaces, verify the motor against the drive’s rated and peak output capability. The motor’s rated current must remain within the drive’s thermal operating envelope, and peak demand must not exceed the drive’s permitted transient output. Motor insulation class, feedback type, resolver pole pairs, cable lengths, and the manufacturer’s configuration restrictions also matter.
The Parker SLVD-N listing is specifically qualified as supporting motor ratings up to approximately 2.2 kW or 3 hp and rated output up to 8.5 A continuous depending on configuration. That wording cannot be ignored: the motor combination, cooling conditions, and selected configuration determine the permitted operating point. Likewise, the Kollmorgen S70602 servo drive listing describes an S7000 digital servo drive with 120/240 V AC input and a 6.5 A three-phase output. The separate Kollmorgen S60001S64001 listing states approximately 6.4 kW with 120/240 VAC three-phase input. Neither output rating establishes automatic compatibility with a particular motor.
The shorter Rexroth W0018 listing describes an 18 A, 7.5 kW-class servo output, but it also lists SERCOS and a used condition. That entry cannot be matched against an EtherCAT machine merely by comparing current and power.
Braking energy is another system-level consideration. The Mitsubishi FR-CV-7.5K listing shows that compatible MR-J4-700B systems can return braking energy to a 200-240 V AC supply through a dedicated regenerative converter. This changes what must be ordered alongside the drive. A replacement plan may therefore require more than a one-for-one drive substitution.
Provenance, Firmware and the Used-Unit Checklist
A used servo drive requires evidence beyond the order code and a powered display. Obtain condition-test records and verify that the control supply is stable before functional testing. Export the parameter set and record the installed firmware before removing the drive from its machine. These steps preserve the axis configuration and make later restoration or comparison possible.
Inspect connectors, cable entries, cooling fans or blowers, and the surrounding enclosure for damage. Check DC-bus capacitor condition after long storage; age-related deterioration may not be visible from outside the unit. Retain labels, terminal photographs, and the removed drive’s original documentation so the installed unit can be identified unambiguously.
Safety functions must also be confirmed before production resumes. Document a commissioning check of the STO or enable circuits rather than assuming that control power and communication indicate a safe machine. Follow the detailed Rexroth IndraDrive servo commissioning guidance for the commissioning process, then use the Servo drive gain tuning guidance for loop and inertia-related tuning. A tested drive can still produce unstable motion if its feedback, enable chain, or tuning state is incorrect.
| Drive listing | What our listing states | Hard matching constraint | What you must still confirm |
|---|---|---|---|
| HCS01.1E-W0018-A-03-B-ET-EC-NN-L4 | 3 x 400-480 V AC input, 18 A, 7.5 kW, EtherCAT, encoder evaluation, integrated L4 filter | Voltage class and EtherCAT network compatibility | Exact manufacturer order code, nameplate, firmware, connectors, and enclosure requirements |
| HCS01.1E-W0018-A-03-B-ET-EC-NN-L3 | 230 V AC, 1.8 kW, EtherCAT, 16-bit feedback, 0 to 55 C ambient, IP65 | Supply voltage and feedback/interface compatibility | Physical unit, nameplate, feedback connector, environmental installation, and complete suffix meaning |
| Kollmorgen S70602-NAPMNA | S7000 drive, 120/240 V AC input, 6.5 A three-phase output, encoder feedback | Supply class, output current, and command interface | Motor configuration, encoder details, pulse/direction or analog requirements, and protection |
| Parker SLVD-N SLVD2NSE | 220-240 V AC three-phase, 50/60 Hz, 24 V DC control, up to 2.2 kW or 3 hp, up to 8.5 A continuous | Control supply, voltage class, and configuration-dependent output | Motor selection, feedback device, command type, and the exact permitted rating for that configuration |
Frequently Asked Questions
Can the same HCS01.1E-W0018 order code identify both the L4 and L3 listings?
The shared portion alone does not. The digits after the current field and the trailing suffix groups define the delivered configuration. Confirm the complete manufacturer order code, the physical nameplate, and the manufacturer datasheet for the actual unit.
Is an EtherCAT drive interchangeable with a SERCOS III drive?
Not as a drop-in replacement. The communications hardware, master configuration, wiring, and device description must match. A listing naming both interfaces also requires confirmation of the firmware option actually fitted.
Does 16-bit or 17-bit feedback resolution determine compatibility by itself?
No. Resolution is only one element. Feedback technology, absolute or incremental capability, memory or battery requirements, resolver pole pairs, and connector pinout must also match the motor and cabling.
Can a drive with the correct power rating be connected to any motor of that rating?
No. Rated and peak current, motor thermal class, feedback, pole-pair information, cooling, and configuration restrictions determine the permissible match. A current field describes drive capability, not unconditional motor approval.
What records should be retained when replacing a used drive?
Retain condition-test results, nameplate details, firmware and exported parameters, connector inspection, storage history, and documented STO or enable-circuit commissioning checks. These records distinguish the installed configuration from assumptions based only on the listing.
A servo-drive order code must be read as a complete configuration statement. The decisive evidence is the exact manufacturer order code together with the physical nameplate and manufacturer datasheet, not a shared model fragment or a catalogue title. Check voltage, current, feedback, communications, firmware, enclosure, and motor constraints before approving a replacement.
Our team can cross-reference the exact part number and lead time against the required configuration. Send us the complete drive code, nameplate details, motor information, and the original failure or retrofit context for a compatibility review.
